F3389 GLEASON 641 HYPOID SPIRAL BEVEL GEAR GENERATOR

Category:

Description

Serial No:   764610

Model:            641

MFD:  1980

 

Capacities:

Extreme Ratio:                                                                        10.1

Root Angle Range:                                                                 -8° to 90°

Maximum Gear Diameter:                                                      406.40mm

Face Width:                                                                            66mm

Maximum Cutting Capacity:                                                  2DP,    12.7 MOD

Full Depth:                                                                              25.4mm

Index Range:                                                                           5 – 10 Inclusive

Examples of Maximum Gear Pitch Diameters With 35”

Gear Spiral Angle & Maximum cutter Diameter At The Following Ratios

1 x 1                                                                                        342.9mm

3 x 1                                                                                        406.4mm

5 x 1                                                                                        406.4mm

Maximum Radial Setting:                                                      177.4mm

Work Spindle Diameter of Taper Hole:

Large End:                                                                              99.22mm

Taper Per Foot:                                                                       15.48mm

Depth of Taper:                                                                       152.44mm

Diameter of Hole Through Spindle:                                       77.79mm

Cutter Diameters Utilised:                                          100, 125, 160, 200, 250, 300mm

Cutting Speeds:                                                                       15 – 250 Rpm

Cycle Time Infinitely Variable:                                  4.5 Seconds / Tooth Minimum

Work Head Settings:

Offset Above Centre:                                                              57.15mm Maximum

Offset Below Centre:                          5                                  7.15mm Maximum

Machine Centre to Nose of Spindle:                                       368.3mm Maximum

 

Electrics:                     415v, 3ph, 50 Cycles:

Cutter Drive Motor:    10 / 5 HP

 

Approximate Dimensions:    3330 x 2160 x 2110mm

Approximate Weight:           13,500kg

Description

Serial No:   764610

Model:            641

MFD:  1980

 

Capacities:

Extreme Ratio:                                                                        10.1

Root Angle Range:                                                                 -8° to 90°

Maximum Gear Diameter:                                                      406.40mm

Face Width:                                                                            66mm

Maximum Cutting Capacity:                                                  2DP,    12.7 MOD

Full Depth:                                                                              25.4mm

Index Range:                                                                           5 – 10 Inclusive

Examples of Maximum Gear Pitch Diameters With 35”

Gear Spiral Angle & Maximum cutter Diameter At The Following Ratios

1 x 1                                                                                        342.9mm

3 x 1                                                                                        406.4mm

5 x 1                                                                                        406.4mm

Maximum Radial Setting:                                                      177.4mm

Work Spindle Diameter of Taper Hole:

Large End:                                                                              99.22mm

Taper Per Foot:                                                                       15.48mm

Depth of Taper:                                                                       152.44mm

Diameter of Hole Through Spindle:                                       77.79mm

Cutter Diameters Utilised:                                          100, 125, 160, 200, 250, 300mm

Cutting Speeds:                                                                       15 – 250 Rpm

Cycle Time Infinitely Variable:                                  4.5 Seconds / Tooth Minimum

Work Head Settings:

Offset Above Centre:                                                              57.15mm Maximum

Offset Below Centre:                          5                                  7.15mm Maximum

Machine Centre to Nose of Spindle:                                       368.3mm Maximum

 

Electrics:                     415v, 3ph, 50 Cycles:

Cutter Drive Motor:    10 / 5 HP

 

Approximate Dimensions:    3330 x 2160 x 2110mm

Approximate Weight:           13,500kg

Menu
Basket

No products in the basket.